PowerCenter Minitower 132 Especificaciones Pagina 1

CONFIDENTIAL 1 PowerWave ª PowerWave ª Certification ModuleCertification Module PowerWave MT Minitower 120/132/150 PowerWave ª MT Specifications

CONFIDENTIAL 10 NNNNooootttteeee:::: All DIMMs must be 168-pin, fast-paged mode, 70-nanosecond RAM access time or faster. ThePowerWave has eight DI

CONFIDENTIAL112. Lower the DIMM squarely into the slot so that the notches in the DIMM line up with the notches in the slot. Slide the contacts straig

CONFIDENTIAL12Removing the CPU1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).1. Lay the machine on its side, open

CONFIDENTIAL13the contact edge of the CPU card. 2. Lower the CPU card squarely into the slot so that the notch in the CPU card lines up with the notch

CONFIDENTIAL14Removing the Cache1. Remove the chassis cover. (refer to Chassis Cover Removal/Installation on page 6).2. Locate the cache card (refer t

CONFIDENTIAL15NNNNooootttteeee:::: Before you install any expansion cards, be sure that the combined power consumption of theexpansion cards does not

CONFIDENTIAL166. Hold the PCI card (contacts facing down) with one hand at each end. Notice that there is a notch in the contact edge of the PCI card.

CONFIDENTIAL178. Connect any wires or cables to the PCI card necessary for its proper operation.9. Reset the CUDA (refer to CUDA Reset on page 4).10.

CONFIDENTIAL18Removing the PCI Riser Card1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Locate the riser card

CONFIDENTIAL192. Replace the support beam. First, fit the forward end of the stabilizer bar into the two small cut-outs in the front panel of the met

CONFIDENTIAL 2 CPU PowerPC 604 at 120, 132 or 150MHz Main Logic Board Tsunami (Comparable to a Macintosh 9500) CPU Upgrade Available via daught

CONFIDENTIAL20Removing the 3.5-inch Drive1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Remove the single scre

CONFIDENTIAL214. The drive cage will swing down and into the computer. Replace the screw that secures the drive cage to the back wall of the chassis.

CONFIDENTIAL22Removing 5.25-inch Drives1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6).2. Disconnect all cables th

CONFIDENTIAL233. Reset the CUDA (refer to CUDA Reset on page 4).4. Install the chassis cover (refer to Chassis Cover Removal/Installation on page 6).F

CONFIDENTIAL24Removing the Floppy Disk Drive5. Remove the front bezel (refer to Front Bezel Removal/Installation on page 8).6. Place the computer on i

CONFIDENTIAL25Installing the Floppy Disk Drive1. Slide the drive into the bay and align the holes in the drive with the holes in the bay. 2. Insert tw

CONFIDENTIAL26Removing the MLB (Main Logic Board)1. Remove the chassis cover (refer to Chassis Cover Removal/Installation on page 6). 2. Remove the CP

CONFIDENTIAL27Installing the MLB1. Slide the MLB into the chassis from the bottom. Lay the board flat and align the mounting holes with the posts.2. R

CONFIDENTIAL28Removing the Power Supply1. Remove the chassis cover. (refer to Chassis Cover Removal/Installation on page 6).2. Swing the 3.5-inch driv

CONFIDENTIAL29¥ the first screw is located above and to the left on the chassis¥ the second screw is located below and to the left on the chassis¥ the

CONFIDENTIAL 3 To ensure your personal safety as well as prevent unnecessary damage to the computer, please follow all safety precautions when perfor

CONFIDENTIAL30This module was written and designed by: Michael Scott Clay.Additional contributions by:Shane NestleJeff PryorEdited byMark WoodLaurie V

CONFIDENTIAL 4 The CUDA Reset button is a small red button located on the Main Logic Board. Depressing this button resets the CUDA Microcontroller Ch

CONFIDENTIAL 5MLB DiagramMLB Diagram

CONFIDENTIAL 6 Removing the Chassis Cover 1. Shut down the computer and turn off all external devices. If you do not have a grounding strap, leave t

CONFIDENTIAL 7 2. Screw the thumb screw into the rear of the chassis.3. Reconnect the cables to the machine. Front Bezel

CONFIDENTIAL 8 Removing the Front Bezel Cover 1. Remove the chassis cover ( refer to Chassis Cover Removal/Installation on page 6). 2. Disengage th

CONFIDENTIAL 9 Installing the Front Bezel 1. Connect the necessary wires to their respective ports on the main logic board. 2. Line up the two tabs